FAQ
G5
G5
Effects
When I use the G5 connected to a guitar amp, high frequencies are exaggerated and the sound is painful.
Open the GLOBAL menu and check the OUTPUT parameter. If set to DIRECT, which is for line connections, a painful high-frequency sound will result. Change the setting to the one most appropriate for the type of guitar amp that you are using. For details, see page 23 of the Operation Manual.
Is it possible to output the effected sound and the original guitar sound at the same time?
Yes, it is possible. Set the XLR BALANCED OUT connector PRE/POST switch to PRE. Set this way, the main OUTPUT jacks will output the effected sound, while the XLR connector will output the original guitar sound at the same time.
Is there a pickup selection function?
No. There is no menu for settings related to the characteristics of single coil, humbucker and other types of pickups.
The volume levels of programmed patches are different. How do I make them the same?
Use the PATCH LEVEL parameter to adjust the volume of each patch appropriately. For details about the PATCH LEVEL parameter, see page 18 of the Operation Manual.
When changing patches, is it possible to not change the sound until after I have confirmed it?
No, it is not possible. The G5 does not have a patch preselect function.
When I use distortion effects, the noise increases.
As a general rule, not just with ZOOM effect processors, distortion sounds are created by amplifying the input signal. When this is done, small noises picked up by the guitar pickups and cables are also amplified. If you are using a distortion effect and noise that you hear when you are not playing is bothering you, try using the ZNR (Zoom Noise Reduction) effect with the distortion effect.
If I connect an FS01 foot switch, which is sold separately, what will I be able to do with it?
If you connect an FS01 foot switch, you will be able to use it to bypass the effects, turn the tuner on/off, tap the tempo for use with rhythms, the looper and effects, and mute the delay input. For details, see page 19 of the Operation Manual.
Is it possible to use a foot switch to tap the tempo used for delay times and modulation rates?
This is not possible using the foot switches on the G5. If you want to tap the tempo for delay times and modulation rates while playing guitar, you will need an FS01 foot switch (sold separately).
Also, please follow the procedures below to tap the tempo with an FS01 foot switch.
1) Select "TAP TEMPO" from the [CTRL SW] setting in the TOTAL menu.
2) Set the TIME/RATE parameter of the desired effect to a note symbol(♪).
If I connect an FP02 expression pedal, which is sold separately, what will I be able to do with it?
If you connect an FP02 expression pedal, you will be able to use it as a volume pedal. However, it's not possible to control any other effect parameters.
Is it possible to restore just one specific effect patch to its factory default?
No, it is not possible to do so on the G5 itself. However, you can restore a specific patch to its factory default settings using the Edit&Share software.
USB
Please tell me what operating systems are supported for using the G5 as a USB audio interface.
The following operating systems are supported for using the G3 as a USB audio interface.
Windows
■ Windows XP SP3 or later (32bit)
■ Windows Vista SP1 or later (32bit/64bit)
■ Windows 7 (32bit/64bit)
Macintosh
■ Mac OS X v10.5.8 or later
■ Mac OS X v10.6.5 or later
■ Mac OS X v10.7
What are the specifications of the USB audio interface?
The specifications of the USB audio interface are as follows.
■ Quantization bit-rate: 16-bit
■ Sampling frequency: 44.1 kHz
■ Number of input channels: 2 (stereo L/R)
■ Number of output channels: 2 (stereo L/R)
Can the G5 USB audio interface be used with DAW software other than Cubase LE?
Since the G5 audio interface should be recognized as a standard Windows or Macintosh audio device, you can use it with other DAW software.
Furthermore, you can also use it with Windows Media Player, Apple iTunes and other audio playback software, allowing you to play along with your favorite music. For information about how to set up other DAW software, please check directly with the software makers.
I am able to use the USB audio interface to record, but no sound comes out of my computer speakers. What should I do?
When using the G5 as a USB audio interface, sound from the computer is output through the G5. Connect speakers to the G5 instead of the computer.
When I record to DAW software using the G5 USB audio interface, it sounds like a flanger effect is being added.
If the DAW software’s “echo back” function, which sends the input signal back to the outputs during recording, is on (input monitoring on), the signal from the DAW software will be output slightly after the direct output of the G5, resulting in a sound like a flanger. If you want to use the DAW software’s “echo back” function, set the USB AUDIO MONITOR parameter to “100.” For details, see page 22 of the Operation Manual.
Can I adjust the recording level sent to my DAW software?
Yes, you can. Open the GLOBAL menu and use the USB AUDIO setting to adjust the REC GAIN parameter. For details, see page 22 of the Operation Manual.
Can the unit operate on USB bus power?
No, the unit does not support operation on USB bus power supplied by the computer.
Is a USB cable included?
No, a USB cable is not included. Please use a commercially-available USB cable (AB type).
Other Topics
While using Edit&Share software, switching the bank from the unit does not work properly.
This problem can be corrected by updating the system software to version 1.10 or later. Go to the
DOWNLOAD page, download the latest version of the system software, and perform the update procedure.
Can I use the looper function and the rhythm function at the same time?
Yes, you can. Follow these procedures.
1) Press the RHYTHM key to start playback of the desired rhythm pattern.
2) Press foot switch 3 to return to the Home Screens.
3) Press and hold foot switch 3 for a second to activate the looper function.
Hint: If you set the TIME parameter to a note mark (♪), you can record phrases in sync with the rhythm.
When using the looper function, can I UNDO/REDO with a foot switch?
Yes, you can. You can use a foot switch while playing the guitar to UNDO/REDO an overdubbed phrase. You can also set Loop playback to stop after fading out, which you can use when looping in real-time during performances.
How do I activate Cubase LE?
Is it possible to adjust the volume when monitoring the output of the G5 using headphones?
Yes it is possible. Open the GLOBAL menu and adjust the G5 output volume (MASTER LEVEL). For details, see page 20 of the Operation Manual.
Can I save the rhythm pattern, tempo and level settings?
Yes, the rhythm pattern, tempo and level settings are automatically saved even when you turn the power off.
Does the G5 have an AUX IN jack to allow the connection of MP3 players and other devices?
No, it does not have an AUX IN jack. However, you can use the USB audio interface function to output playback from Windows Media Player, Apple iTunes or similar software at the same time that you use the G5. You can, for example, play your guitar along to music that you like.
